How to Replace a kia car key replacement Sportage Replacement Key

For a number of Kia models keys, the key has the keyless entry system that is built into the key. The key functions like remote controls, and can be exchanged by an Kia dealer.

Key fobs may stop working due to a variety of reasons, including batteries that are dead, worn-out buttons signal interference, or water damage. Here are some helpful tips to help you get your Kia sportage replacement key working again.

How to replace a remote key or a smartkey?

No matter if your Kia is equipped with an intelligent key, remote key, push-to-start keys, Back or a standard non-transponder key made of metal, the battery in these keys will eventually require replacing. This is especially in the event that your vehicle displays a message that indicates that the remote or smart key is not powered by the battery.

Luckily, it's a relatively simple process. To replace the battery of the keyfob take out your mechanical key from the slit that is located at the back of the fob. Then, pull the cover open. Inside the key fob, there will be the small screw that holds the battery in its place. Remove the old battery by removing the screw with the help of a small screwdriver. Install the new battery and close the cut on the key fob.

Test the key fob by pressing the lock/unlock buttons. You're in good shape when the doors lock or unlock as you expect. You can now use the hands-free feature to lock and unlock your kia ceed key fob when your fingers get cold or when you need to run errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming done. This requires a programming machine, which is only available to the locksmith in the automotive or dealer. Other keys (non-transponder metal keys) do not require programming. If your keys need to be programmed, you will need to be aware of the key code number printed on the key code tag and record the number in a secure place.

How do you replace the battery?

If your Kia key fob isn't responding when you press the lock or click web page unlock button on the fob, this is a signal that the battery needs to be replaced. A low battery could cause other issues such as the check engine light flashing on or delayed engine cranking. Fortunately replacing the battery on the key fob is a fairly simple DIY project that requires only the most basic tools.

Before you begin ensure that your vehicle is off and all doors are closed. Find the small metal or plastic piece on the bottom of the key fob. Move it until the key comes out. The key can be placed inside the driver door handle to unlock your car.

To replace the key fob battery, take off the cover at the rear and use a plier bar tool to remove the latch holding the black negative battery cable. Remove the old battery and align the new one to ensure that the "+" positive side is facing you, while the "-" negative side is facing the fob's electrical contacts made of metal. Avoid using excessive force when pushing the new CR2032 into place to avoid damaging or bending the metal contacts.

After the new battery has been installed after which you turn the key fob off and then on in the ignition for a few times until the door locks cycle. You can then test the Kia's key fob again to confirm that it is working correctly.

How to replace the smart key?

Depending on the model of your Kia Sportage, you may have a standard key fob or a smart key. The smart key is equipped with an embedded mechanical key blade while the standard keyfob does not. Both kinds of key fobs come with batteries inside that will eventually need to be replaced. This is a straightforward process which takes just two minutes.

Before you start it is essential to make sure that you are on a flat surface with good lighting and that your Kia is turned off. Remember that the fob has small pieces that could be thrown off if you're not careful.

The first step is to find the small release button that is located on the backside of the fob. It's either a circular button or a rectangular slot. You can open the key fob by pressing the button.

Once the key fob is opened, remove the battery. The new battery should be a CR-2032, and can be purchased online or at your local auto parts store. When you are done with the battery, you should be able to lock, unlock and start your vehicle using your key fob - even if the engine isn't running!

How to replace the mechanical key

The Kia keyfob can be a fantastic convenience that lets us lock or unlock our car simply by pressing the button. Like any other device it will encounter issues at times. There are solutions to fix these problems and keep your key fobs functioning for many years.

A dead or low-quality battery is one of the most common issues. This can cause your fob to stop working or operate intermittently. If this is the case it is time to replace the battery an entirely new battery.

If this doesn't solve the problem Try using a standard flathead screwdriver and wedge it into the fob's plastic casing. Be careful not to damage any internal components, or scratch the plastic. When the battery is open, carefully take off the old battery and replace it with a brand new one.

Once the new battery is in, close and open the doors using the mechanical key (every Kia fob comes with an emergency mechanical key that will fit into the slot). Test the key fob and ensure that it's working properly. If the fob still isn't functioning, contact an expert locksmith or dealer to solve the issue. To avoid lockouts in the future, make sure you get an emergency key that will work in all of the door and trunk cylinders.